Wiki

Wiki Help

Clocks: Difference between revisions
No edit summary
Line 1: Line 1:
In this page we cover electrical, electromechanical and electronic clocks, outlining principles of operation and the often limited options for repair. Repairing mechanical clocks is a highly skilld process, not covered here.
In this page we cover mechanical, electrical, electromechanical and electronic clocks, outlining the repair options
<div class="showtoc">
<div class="showtoc">
__TOC__
__TOC__
Line 5: Line 5:


==Summary==
==Summary==
Clocks have seen many changes with evolving technology, from pre-history to the present day. This is a fascinating topic, and will give you an insight into what repairs might be possible.
With the march of technology, many different types of clock have appeared, and with them, differing possibilities and options for repair, whar are outlined here. Some are cherished items for which repair is sought for nostalgic reasons whereas others may be mass-produced with very limited repair options. Restoration and repair of vintage wind-up clocks is a highly skilled craft but even for these a service clean may be within the capability of any careful fixer.


Repair of traditional wind-up clocks and watches is a highly skilled process, well beyond the scope of this page. The plastic gear train in many quartz clocks can be disassembled and reassembled relatively easily, but the problem is likely to be wear, which can't be reversed.
The history and principles of operation of the many types of clock is a fascinating subject. See [[Clocks - Basic Principles]] for an outline, which will underpin much of the content of this page.
 
Changing watch batteries is fairly straightforward though some special tools may be required. A separate Wiki page is in preparation.
 
If you can contribute anything on repair, or on mechanical clocks, please feel free to add it or to leave your wisdom in the associated [[Talk:Clocks|Discuss]] page.


===Safety===
===Safety===
Line 17: Line 13:
::Old mains-driven clocks often have poor insulation and without an earth connection to the metal frame. This makes them potentially lethal and a fire risk.
::Old mains-driven clocks often have poor insulation and without an earth connection to the metal frame. This makes them potentially lethal and a fire risk.
::Should you be tempted to try dismantling and repairing a wind-up clock, treat the spring with the utmost respect. It can be very dangerous if released suddenly. If the coiled metal spring escapes from its housing it can instantly turn into a flying snake knife capable of removing fingers and eyes.
::Should you be tempted to try dismantling and repairing a wind-up clock, treat the spring with the utmost respect. It can be very dangerous if released suddenly. If the coiled metal spring escapes from its housing it can instantly turn into a flying snake knife capable of removing fingers and eyes.
::You may miss your bus if your clock is wrong. This could really spoil your day.
==Basic Principles==
All clocks can be considered to be composed of two parts:
* Some kind of time standard for measuring the passage of time, and
* Some kind of display for displaying the measured time.
In principle you can mix and match the two, so for the purposes of explaining basic principles it's worth considering them separately.
===Time Standards===
====Historical====
[[Wikipedia:Water_clock|Water clocks]] have been used since antiquity. They depend on the steady flow of water through a small orifice to measure the passage of time. But the rate of flow is dependant on the viscosity of water, which varies with temperature. This limits their accuracy.
The [[Wikipedia:Hourglass|hourglass]] or sand clock uses sand or some other granular substance instead of water. This is less dependant on temperature and hence more accurate. They are still in use as egg timers.
A constant rate of combustion has also been used historically to measure time. A candle clock has time divisions marked along the length of a candle. A particularly ingenious variant is the Chinese incense clock. This consists of a series of weights suspended above a metal tray, each held by a piece of string. The strings, equally spaced, are stretched across an incense stick. As the stick burns it burns through the strings one by one, giving an audible indication of the passage of time as the weights fall onto the tray. A fine example can be seen at the [https://www.museumoftimekeeping.org.uk/ Museum of Timekeeping]. As with the flow of water or sand, a rate of combustion depends on various environmental conditions, making it a poor measure of the passage of time.
Astronomical phenomena such as the passage of the sun across the sky are the most ancient accurate means of telling the time. [[Wikipedia:Sundial|Sundials]] were used in ancient Babylon and Egypt, and remain a nice garden feature, but even the most ardent gardeners are likely to refer to a wristwatch rather than a sundial (even if the sun is out) in order to decide when to take their tea break.
Having discovered the moons of Jupiter, [[Wikipedia:Galileo_Galilei|Galileo]] worked on a method of using a knowledge of their orbits to tell the time. Comparing the time so determined with the solar time at your current location offered an accurate means of [[Wikipedia:History_of_longitude|determining longitude]].
====Mechanical====
Unlike water and sand clocks, pendulums and balance wheels depend on a repetitive motion taking a well defined period of time. Furthermore, compensation can fairly easily be made for variations with temperature. Such clocks were refined in the 18th Century most notably by [[Wikipedia:John_Harrison|John Harrison]], spurred by the need for an accurate timepiece for navigation at sea.
All these clocks rely on the simple fact that if a mass is subject to a force tending to restore it to an equilibrium position, the magnitude of the force being in direct proportion to the distance from that equilibrium position, the mass will execute "[[Wikipedia:Simple_harmonic_motion|Simple Harmonic Motion]]". This is characterised by an oscillation or vibration at a well defined [[Glossary:Frequency|frequency]], independant of the amplitude of the motion. This is why a wind-up clock doesn't run slower as it runs down, as a wind-up toy car would, for example.
In practical clocks, an escapement is needed to give the pendulum or balance wheel the regular kicks it needs to keep it in motion indefinitely. This can be powered by a spring or in the case of a grandfather clock, by weights. Occasionally in more modern clocks you might find an electrical mechanism.
Most wind-up clocks will in fact run slightly slower as the spring unwinds and looses tension. The [[wikipedia:Fusee_(horology)|fusee]] mechanism, invented in the 15th Century uses a cone-shaped pulley to decrease the gearing applied to the sping as it winds down, so maintaning a constant torque applied to the escapement. The bulk, complication, expense and issues with reliability and maintenance caused it to fall out of favour while other improvements made it less necessary.
Very rarely you might find a clock which uses a tuning fork kept vibrating electronically as the time standard instead of a pendulum or balance wheel.
====Quartz crystals====
These in fact also depend on a mechanical vibration, but sustained electronically and at a much higher frequency.
Quartz is an example of a [[Glossary:Piezo|piezoelectric material]], that is, an electical charge appears on opposite faces if you stress it, and conversely, applying a voltage will cause it to deform slightly. Using this property, a piece of quartz is carefully cut and ground so as to "ring" at a specific resonant frequency and is kept in oscillation electronically.
Quartz crystals used in simple clocks and watches nearly always have a resonant frequency of 32,768[[Glossary:Hertz|Hz]]. This might seem an odd number until you realise that halving it 15 times successively gives a 1 second tick. This is easily done with simple electronic circuits. An advantage of such a high frequency is that you just have to count the oscillations in 1 second and check there are exactly 32,768 (not even just one more or one less) to assure the accuracy of your clock to a minute in 3 weeks! If a clock ticks just a few times a second, you would have to count the ticks for a much longer time to achieve the same accuracy. Fine adjustment is possible by connecting a variable [[Glossary:Capacitor|capacitor]] in the circuit with the crystal.
Quartz crystals provide a more accurate and more stable time source than a mechanical clock but nevertheless they are somewhat temperature dependant. Those used in cheap clocks typically have an accuracy of a few seconds per day. Additionally, quartz crystals are subject to ageing, causing a small additional drift over a number of years, and are also affected by the heat of the soldering process at the time of manufacture
In a [[Glossary:TCXO|Temperature Compensated Crystal Oscillator]] (TCXO) the control [[Glossary:Integrated Circuit|IC]] contains a temperature sensor and the crystal is incorporated in the same package. This allows the IC to compensate for temperature variations by adjusting the capacitance included in the crystal oscillator. By this means, an accuracy of 10 seconds per year is achievable.
====MEMS Resonators====
A resonator can also be constructed as a [[GLOSSARY:MEMS|MEMS]] (MicroElectroMechanical System) device in which a microscopic mechanical resonator and the required control circuitry are all fabricated on a single silicon chip. This can give an accuracy similar to a [[Glossary:TCXO|TCXO]], but it is inherently much less temperature dependant, less subject to ageing and the effects of soldering, and at the same time much more rugged.
====Atomic clocks====
These are the most accurate clocks available, the best typically gaining or losing no more than the equivalent of 1 second in 30 million years, but they are very expensive and usually very bulky. Chip-scale versions are now available but these are still by no means cheap.
Atomic clocks depend not on a mechanical vibration but on an atomic resonance, most usually in caesium or rubidium atoms. In fact the second is now officially defined as 9,192,631,770 oscillations in a caesioum-133 atom. National and international time standards are based on the averages of a number of atomic clocks, and it is on these that all the remaining time standards are based.
Rubidium frequency standards (not quite as accurate as caesium ones) are widely used in cell phone towers. In fact, if you wanted your very own atomic clock there are second hand ones from decommissioned cell towers going on eBay for only a few hundred pounds!
Atomic clocks operate at gigahertz frequencies, but even greater accuracy still can be achieved by using light, which is in the hundreds of terahertz range. The Nobel Prize for Physics in 2005 was awarded for work on applying optical [[wikipedia:Frequency_comb|frequency combs]] to lock an atomic clock to the frequency of the light from a laser.
====Radio Time Signals====
In the UK, the National Physical Laboratory's time standard is based on three atomic clocks, and is broadcast as the "[[Wikipedia:Time_from_NPL_(MSF)|MSF Signal]]". This can be received across much of northern and western Europe. Numerous [[Wikipedia:Radio_clock#List_of_radio_time_signal_stations|other radio time signals]] are available in different parts of the world.
Domestic clocks which automatically synchronise with one of these radio broadcasts are widely available, sold as "radio controlled clocks", or even "atomic clocks" though they are actually using someone else's atomic clock!


====GPS====
==Wind-up clocks==
Satellite navigation depends on a constellation of satellites each with its own on-board atomic clock and transmitting a signal containing encoded time information. Consequently not only can you get your geographical position by receiving these signals, but also an extremely accurate time.
 
====Pulsars====
[[Wikipedia:Neutron star|Neutron stars]] are the incredibly dense remains of dead stars not quite massive enough to collapse into a black hole. A teaspoonful of their matter might weigh as much as a mountain. As they spin, their magnetic field may generate beams of radio waves or x-rays which sweep across space like the beams of a lighthouse. When these are detectable as a series of pulses by a radio or x-ray telescope, they are then known as [[Wikipedia:Pulsar|pulsars]]. Being so massive, the pulses are extremely regular and could be used as the basis of a highly accurate clock. There are more convenient methods of telling the time here on earth, but if you're navigating across the solar system or beyond, comparing the times of arrival of the pulses from several different pulsars can make a very accurate and effective means of [[Wikipedia:Pulsar-based_navigation|telling where you are]].
 
====AC Mains====
The AC mains supply has a nominal frequency of 50Hz (or 60Hz in some regions). Although the frequency can vary slightly, the total number of cycles in a day is very carefully controlled. The reason for this is that if demand exceeds supply, all the generators naturally tend to slow down under the load, so reducing the frequency, or conversly, speed up in the case of over-supply. Hence the frequency is used as a vital tool in matching supply to demand in the National Grid.
 
A useful consequence is that the mains supply can be used as a time standard with guaranteed long term accuracy, though like several others, it's in reality a 2nd hand atomic clock.
 
====Internet Time Sources====
Your computer, smartphone or tablet contains a quartz crystal from which it determines the time on a continuous basis, but this is regularly synchronised with time sources available on the Internet. [[Wikipedia:Network_Time_Protocol|NTP]] (Network Time Protocol) is the means by which any computer on the Internet can request the time from a chosen time server and estimate the adjustment required to account for the transmission delay. The necessary correction to the system clock is then made gradually so as to avoid a sudden jump in the time, especially a jump backwards which might be very confusing to some applications.
 
NTP time sources are each given a "Stratum" classification. A Stratum 0 reference is an actual atomic clock or equally authoritative time source. A Stratum 1 device periodically synchronises against a Stratum 0 reference. This might be a rubidium clock or a server accessble on the Internet. An organisation might have its own Stratum 2 server which periodically queries a Stratum 1 server, and in turn is used as a reference by Stratum 3 devices, which might be employees' PCs.
 
===Time Displays===
====Analogue Displays====
We all learned at an early age to tell the time from an analogue clock face with a minute and an hour hand, and for centuries, this has been the standard method of displaying the time. Imaginative novelty variations on the idea are sometimes seen.
 
In fact, early mechanical clocks only had an hour hand as they were terrible timekeepers, perhaps loosing as much as 45 minutes a day. Furthermore, domestic clocks would be set daily from the church clock, which in turn would be set from the church sundial, or more likely on a cloudy day from the movement of the verger's bowels. Hence, a minute hand would be pretty useless for telling the time of day. The widespread introduction of the pendulam by clock makers in the 17th Century suddenly made possible domestic clocks with a timekeeping accuracy of a few seconds a week!
 
====Digital Displays====
Electromechanical digital displays have been around for many years, the commonest form being the flip-down display. A series of cards flip down one after another, each card containing the top half of a digit on one side and the bottom half of the next digit on the reverse. These clocks are now often collector's items or cherished heirlooms. They are described in their own page: [[How flip clocks work]].
 
[[Wikipedia:Nixie_tube|Nixie tubes]] were used as an early form of digital display. A Nixie tube consists of a glass envelope containing neon gas and 10 digits, each formed out of wire. Any one of these can be illuminated by applying a voltage to it, causing it to light up with the characteristic orange neon glow. Special driver circuits are required as Nixie tubes need around 150V to work. Nowadays these clocks are purely a novelty item, popular amongst the maker community.
 
Modern digital clocks generally use a familiar 7-segment display. The entire display may be formed as an [[Glossary:LCD|LCD]] panel, often including additional symbols for AM/PM or an alarm indication. Alternatively, each segment may be lit by an [[Glossary:LED|LED]], eliminating the need for a back light for it to be seen in thedark. LCDs and LEDs have the advantage of working on similar low voltages to the logic circuits driving them.
 
[[Wikipedia:Vacuum_fluorescent_display|Vacuum flourescent displays]] (VFDs) are most often seen on older devices such as video recorders. Flourescent segments making up the display are housed in an evacuated glass envelope. Streams of electrons cause activated segments to glow, often with a blueish green colour. These displays tend to use higher voltages than most logic circuits but not as high as Nixie tubes.
 
==Clockwork clocks==
These are purely mechanical and are the oldest type of clock still in common use. After many years of service they often stop working because of thickening of lubricating oil and its contamination by dirt, or wear in the bearings and gears. Cheap clocks often fail much sooner.
These are purely mechanical and are the oldest type of clock still in common use. After many years of service they often stop working because of thickening of lubricating oil and its contamination by dirt, or wear in the bearings and gears. Cheap clocks often fail much sooner.


Line 115: Line 22:
Before starting work on any wind-up clock it's essential that you unwind the spring in a controlled manner as its uncontrolled release can cause serious injury. Release the ratchet whilst holding the spring tension with the winder. Allow the spring to unwind by half a turn at a time, or only as much as the rotation of your wrist will allow.
Before starting work on any wind-up clock it's essential that you unwind the spring in a controlled manner as its uncontrolled release can cause serious injury. Release the ratchet whilst holding the spring tension with the winder. Allow the spring to unwind by half a turn at a time, or only as much as the rotation of your wrist will allow.


As with all types of clock with brass bearings and gears, you must only use special clock oil. This leaves no residue as it gradually evaporates, does not disolve any lacquer that might be applied to the brass, and has sufficient surface tension to remain within a bearing.
As with all types of clock with brass bearings and gears, you must only use special clock oil. This leaves no residue as it gradually evaporates, has sufficient surface tension to remain within a bearing, and does not disolve any lacquer that might be applied to the brass.


Following disassembly you can clean all parts with special clock-cleaning ammoniated fluid, and using a nylon brush.
Following disassembly you can clean all parts with special clock-cleaning ammoniated fluid, and using a nylon brush.


An excellent introduction to clock servicing would be a reasonable quality carriage clock that has stopped working. A [https://braintreeclockrepairs.co.uk/2016/01/16/how-to-service-a-carriage-clock-yourself blog posting] at the [https://braintreeclockrepairs.co.uk Braintree Clock Repairs] website takes you step by step through the dismantling, cleaning and reassembly.
An excellent introduction to clock servicing would be a reasonable quality carriage clock that has stopped working. A [https://braintreeclockrepairs.co.uk/2016/01/16/how-to-service-a-carriage-clock-yourself blog posting] at the [https://braintreeclockrepairs.co.uk Braintree Clock Repairs] website takes you step by step through the dismantling, cleaning and reassembly.
Some vintage clocks contain a "fusee". This is a conical pulley driven by the spring, with a chain wound arond it. The purpose is to reduce the gearing of the spring drive as it winds down, compensating for the reduction in its tension. The more constant drive applied to the escapement results in better timekeeping but at the expense of greater bulk, complication and difficulty of service. Other improvements in clock design have led to its gradual abandonment by clockmakers.


Should you get hooked on clock repair the [https://bhi.co.uk National Horological Institute] offer a range of in-person and distance learning courses. Lesson One of their Technician Grade course is [https://bhi.co.uk/wp-content/uploads/2019/05/BHI-DLC-Technician-Grade-SAMPLE.pdf freely available online] - well worth taking a look!
Should you get hooked on clock repair the [https://bhi.co.uk National Horological Institute] offer a range of in-person and distance learning courses. Lesson One of their Technician Grade course is [https://bhi.co.uk/wp-content/uploads/2019/05/BHI-DLC-Technician-Grade-SAMPLE.pdf freely available online] - well worth taking a look!
Line 187: Line 96:
See [[How flip clocks work]].
See [[How flip clocks work]].


==7 segment display clocks==
==Seven segment display clocks==
These may use a quartz crystal, radio signal or the 50Hz mains supply for the time standard.
These may use a quartz crystal, radio signal or the 50Hz mains supply for the time standard.


Line 194: Line 103:


==External links==
==External links==
* [https://www.mpoweruk.com/timekeepers.htm Watch and Clock Movements] at [https://www.mpoweruk.com Electropedia] gives easily understood explanations of everything from pendulum clocks to atomic clocks.
* Rod Elliott's [https://sound-au.com/clocks/index.html Clocks Pages] contain a wealth of information on electric and electronic clocks.
* Rod Elliott's [https://sound-au.com/clocks/index.html Clocks Pages] contain a wealth of information on electric and electronic clocks.
* [https://braintreeclockrepairs.co.uk Braintree Clock Repairs] have lots of articles about clocks on their website. In particular, see [https://braintreeclockrepairs.co.uk/2016/01/16/how-to-service-a-carriage-clock-yourself/ How to repair a carrige clock yourself - the service clean] for a detailed guide to dismantling, cleaning, oiling and reassembling a carriage clock, within the capability of anyone with patience and ordinary levels of skill.
* [https://braintreeclockrepairs.co.uk Braintree Clock Repairs] have lots of articles about clocks on their website. In particular, see [https://braintreeclockrepairs.co.uk/2016/01/16/how-to-service-a-carriage-clock-yourself/ How to repair a carrige clock yourself - the service clean] for a detailed guide to dismantling, cleaning, oiling and reassembling a carriage clock, within the capability of anyone with patience and ordinary levels of skill.


[[Category:Fixing]]
[[Category:Fixing]]

Revision as of 09:50, 19 April 2023

In this page we cover mechanical, electrical, electromechanical and electronic clocks, outlining the repair options

Summary

With the march of technology, many different types of clock have appeared, and with them, differing possibilities and options for repair, whar are outlined here. Some are cherished items for which repair is sought for nostalgic reasons whereas others may be mass-produced with very limited repair options. Restoration and repair of vintage wind-up clocks is a highly skilled craft but even for these a service clean may be within the capability of any careful fixer.

The history and principles of operation of the many types of clock is a fascinating subject. See Clocks - Basic Principles for an outline, which will underpin much of the content of this page.

Safety

Warning03.png
Old mains-driven clocks often have poor insulation and without an earth connection to the metal frame. This makes them potentially lethal and a fire risk.
Should you be tempted to try dismantling and repairing a wind-up clock, treat the spring with the utmost respect. It can be very dangerous if released suddenly. If the coiled metal spring escapes from its housing it can instantly turn into a flying snake knife capable of removing fingers and eyes.

Wind-up clocks

These are purely mechanical and are the oldest type of clock still in common use. After many years of service they often stop working because of thickening of lubricating oil and its contamination by dirt, or wear in the bearings and gears. Cheap clocks often fail much sooner.

Fault-finding and repair

Clock conservation, repair and restoration are highly skilled operations requiring a fully equipped workshop, but a service clean of a simple clock such as a carriage clock is no harder than smartphone repair. A striking clock would harder but only as being more complicated.

Before starting work on any wind-up clock it's essential that you unwind the spring in a controlled manner as its uncontrolled release can cause serious injury. Release the ratchet whilst holding the spring tension with the winder. Allow the spring to unwind by half a turn at a time, or only as much as the rotation of your wrist will allow.

As with all types of clock with brass bearings and gears, you must only use special clock oil. This leaves no residue as it gradually evaporates, has sufficient surface tension to remain within a bearing, and does not disolve any lacquer that might be applied to the brass.

Following disassembly you can clean all parts with special clock-cleaning ammoniated fluid, and using a nylon brush.

An excellent introduction to clock servicing would be a reasonable quality carriage clock that has stopped working. A blog posting at the Braintree Clock Repairs website takes you step by step through the dismantling, cleaning and reassembly.

Some vintage clocks contain a "fusee". This is a conical pulley driven by the spring, with a chain wound arond it. The purpose is to reduce the gearing of the spring drive as it winds down, compensating for the reduction in its tension. The more constant drive applied to the escapement results in better timekeeping but at the expense of greater bulk, complication and difficulty of service. Other improvements in clock design have led to its gradual abandonment by clockmakers.

Should you get hooked on clock repair the National Horological Institute offer a range of in-person and distance learning courses. Lesson One of their Technician Grade course is freely available online - well worth taking a look!

Electrically-assisted clocks

These have a pendulum or a balance wheel like a clockwork clock, but it's kept in motion electrically rather than by a spring or weight.

A fascinating very early example is the earth-driven clock, invented in 1911 by Percival Arthur Benson. Two different metal stakes driven into the ground served as a primitive battery, delivering just a volt or so. This fed an electomagnet which applied a tiny force to a permanent magnet attached to the pendulum. As the pendulam swung back and forth it operated a set of contacts which reversed the direction of the current, so keeping the pendulam in motion.

Fault-finding and repair

In the case of a vintage mains driven clock the insulation and earthing are likely pose serious safety concerns, which must be addressed before going any further.

The first challenge will be to work out how it operates. A common method would be using a transistor to amplify and reinforce a current induced in a coil by a magnet attached to the movement. The transistor could be a germanium type, less reliable and robust than more modern silicon transistors. You can test it quite easily with a multimeter. If you unsolder it, apply a pair of pliers to each lead to act as a heat sink as you apply the iron.

Mains synchronous clocks

These were very popular as accurate mantlepiece and wall clocks before the advent of quartz movements. A synchronous motor rotates at the mains frequency and a gear chain reduces this to drive the second, minute and hour hands.

Fault-finding and repair

First of all, it must be said that there may be serious safety issues with these clocks. For a start, the insulation is likely to be in a poor state, and to make matters worse, they have exposed metal parts and rarely have an earth connection. This means there is a significant risk of electrocution and possibly also of fire. However, this doesn't mean they can't be repaired or restored.

Often, you will find the coil in the motor is open circuit or burnt out (or both). This coil is driven directly by the mains and creates the oscillating magnetic field which turns the motor spindle. Whilst it may be possible to rewind it, it's likely to have many thousands of turns and the wire will be so thin that you'd be unlikely to complete the task without it breaking.

A good alternative is to rewind the coil with fewer turns of somewhat thicker wire and drive it from a low voltage transformer, ideally an AC wall cube type. This has the added benefit of eliminating the risk of electric shock and greatly reducing the fire risk. How to do this is covered in detail at sound.whsites.net/clocks/ocm.html.

Quartz clocks

These rely on the vibrations of a crystal of quartz for their time keeping, rather than a balance wheel or pendulum.

Fault-finding and repair

Sometimes the setting buttons become unreliable. If they are the standard miniature tactile type you may be able to replace them, but often they just consist of a rubber button with a conductive layer underneath which makes the contact between adjacent circuit board traces. You may be able to improve it by cleaning the contacts or by rubbing a 2B (or softer) pencil on the conductive layer, or applying conductive paint such as Bare Conductive. Yet another type of button consists of a piece of domed metal which clicks like the safety button on the lid of a glass jar to make contact with a circuit board trace.

As with many battery operated devices, dead batteries may leak and corrode the contacts, which will need thoroughly cleaning.

If you remove the hands (these just pull off), refit them both precisely on the 12 so that the hour hand will always point at an hour when the minute hand reaches 12.

Quartz Watches

These run off a coin cell which typically lasts around a year. More modern ones may have a lithium coin cell lasting around 3 years.

Fault-finding and repair

You can save money by changing the battery yourself, but you may need special tools.

The back will be either screw-on or snap on. A screw-on back will have several notches into which you can engage a tool to twist it off. You can screw it back on in the same way. Snap-on backs can be harder both to remove and replace. There will be an indentation at some point around the circumference into which you can insert a knife or removal tool. Considerable force may be required so great care is needed especially if you are using a sharp knife, in case it slips. Replacing it also often requires considerable force. If you can't do it between fingers and thumbs you will need a watch press. This comes with several dies of different sizes designed to apply the force to the watch body rather than the glass, which you would be very likely to smash.

Having got inside you will probably have to loosen a very small screw in order swing a contact out of the way so as to remove and replace the battery. Only loosen it as much as you need to as it will be fiddly to replace if it comes right out.

You may be able to clean up the battery contacts if they are corroded, and provided the leaking electrolyte which caused the corrosion hasn't caused any other damage. Any other faults such as water damage may not be feasible to repair.

Radio-controlled clocks

These generally have a quartz clock mechanism for back-up timekeeping, but get an accurate time reference from a radio signal, such as MSF Rugby, against which they synchronise regularly.

The self-setting mechanism relies on the clock being able to detect when the hands are in the 12:00 position. This relies on holes in the minute and hour gears which line up at 12 o'clock. An LED and photodetector sense this position. Some clocks have a slightly more complicated system allowing the clock to run fast until maybe 11:45 and then more slowly so as not to miss 12:00 precisely, or they maybe able to recognise several positions of the hands, avoiding the need to wind forward to 12 o'clock in every case. All these use the same kind of mechanism, though understanding just how the clock recognises different alignments of the holes may not be easy.

Fault-finding and repair

Sometimes the problem with these is quite simply an unsuitable battery. Make sure it's an alkaline type, not a cheap zinc one and not a rechargeable.

If the clock is still running but failing to synchronise with the radio signal, this is likely to be due to a weak battery. It may well be that the clock mechanism will continue working long after the battery voltage has fallen below the minimum needed by the radio receiver.

The other simple explanation for a clock not setting or resetting itself is just that it may be placed somewhere where the radio signal is inadequate. Try leaving it on a windowsill or at a different angle.

The same problems with push buttons occur as with quartz clocks.

There is probably little you can do about mechanical problems. Should you remove the gears it's likely that they will need to be reassembled in the correct orientation for the setting mechanism to work. If you examine them carefully you may find that the critical ones each have a pin hole which needs to be lined up one with another or with a pin hole in the plastic case. Inserting a pin through these holes during reassembly will ensure the correct orientation. This is likely to correspond to the 12:00 position of the hands.

Flip clocks

These are the earliest widely available form of digital clock. The hours and minutes and possibly the day of the week and day of the month are displayed on flip-down cards.

Fault-finding and repair

See How flip clocks work.

Seven segment display clocks

These may use a quartz crystal, radio signal or the 50Hz mains supply for the time standard.

Fault-finding and repair

External links

Retrieved from "https://wiki.restarters.net/index.php?title=Clocks&oldid=8962"
This page was last edited on 19 April 2023, at 09:50.