Advanced hard disk tools: Difference between revisions

No edit summary
Line 3: Line 3:


==Summary==
==Summary==
The [https://en.wikipedia.org/wiki/S.M.A.R.T.#ATA_S.M.A.R.T._attributes S.M.A.R.T.] data returned by a hard disk can give a useful indication of its health but there are other tools that can be used which go well beyond this. WARNING: some of these tools are DANGEROUS and should only be used in a kill-or-cure situation or if you are certain that a full system backup is available.
The [http://en.wikipedia.org/wiki/S.M.A.R.T.#ATA_S.M.A.R.T._attributes S.M.A.R.T.] data returned by a hard disk can give a useful indication of its health but there are other tools that can be used which go well beyond this. WARNING: some of these tools are DANGEROUS and should only be used in a kill-or-cure situation or if you are certain that a full system backup is available.


==ddrescue==
==ddrescue==
Line 42: Line 42:
* Relocate event count
* Relocate event count
* Current pending sectors
* Current pending sectors
See the Wikipedia [https://en.wikipedia.org/wiki/S.M.A.R.T.#ATA_S.M.A.R.T._attributes S.M.A.R.T.] article for further details.
See the Wikipedia [http://en.wikipedia.org/wiki/S.M.A.R.T.#ATA_S.M.A.R.T._attributes S.M.A.R.T.] article for further details.


'''SCAN''' - Scan the disk
'''SCAN''' - Scan the disk

Revision as of 21:37, 9 July 2014

Advanced tools for diagnosing and recovering hard disk problems. (This page is work in progress. Please refrain from editing until the first draft is complete and this note has been removed. Comments under Discussion are nevertheless welcome. And if you think there are plenty of other topics of higher priority than this then you're right - but I just need to do a brain dump of what I've recently learnt before I forget it all.)

Summary

The S.M.A.R.T. data returned by a hard disk can give a useful indication of its health but there are other tools that can be used which go well beyond this. WARNING: some of these tools are DANGEROUS and should only be used in a kill-or-cure situation or if you are certain that a full system backup is available.

ddrescue

Spinrite

gdisk

MHDD

MHDD is a low level diagnostic and maintenance tool that runs under MSDOS or FreeDOS. It's best run from a DOS bootable USB memory stick. If you have Spinrite on a memory stick, add this to it too.

Note that MHDD will destroy data if not used with care.

MHDD is basically a user interface to the ATA command set and more. A key feature is that it accesses the disk direct rather than going through the BIOS and hence gets a more accurate and uncensored view. For example it can read the SMART data even if the BIOS hides it. The following is a very brief survival guide to the most useful functions.

Command line flags

\ENABLEPRIMARY

Normally MHDD disables access to the primary disk on the assumption that this may well be what DOD is running from. Use this command line flag when running from a bootable USB memory stick if it's the primary disk you need to access.

Commands

MHDD issues a prompt, to which you can type a range of commands, a few of which are listed here. (Commands are case-insensitive.)

HELP - Gives a list of commands and brief descriptions

MAN <command> - Gives a fuller description of the named command.

PORT - Issue this command first to get a list of disks, then select the one you want by number.

EID - Report extended ID information from the disk.

SMART ATT - Report values of SMART attributes. (The F8 key is a synonym for this command.) Pay special attention to:

  • Read error rate
  • Relocated sectors count
  • Relocate event count
  • Current pending sectors

See the Wikipedia S.M.A.R.T. article for further details.

SCAN - Scan the disk

The disk is scanned, giving a graphic display of its state, and with the option of remapping bad sectors.

Several options are offered in a pop-up menu, in particular:

  • Start, End - Start and end sectors for the scan, defaulting to the entire disk.
  • Remap - Attempt to remap bad sectors, provided they can be read correctly (with difficulty).
  • Erase delays - Erase sectors which take a long time to read, whether or not correctly. This should cause them to be remapped, but the data is lost.

Blocks of 255 sectors are each represented by a single blob. A brighter greyscale or coloured blob indicates a slow read, suggesting the disk had trouble reading a sector. An "x" indicates a sector was unreadable.

Log files

Log files of a session are created in a sub-folder LOG in text format. Rename the LOG directory after a session so that a new session on a different disk and on another occasion will create new log files.

References

Template:Reflist

External links

  • External links as bullet points