Compact cameras

Fixing digital compact cameras.

Summary

In the years since they became affordable and widely available, digital compact cameras have grown vastly more capable than the film cameras they replaced, but unfortunately not more reliable – there’s much more to go wrong! And when it does, few people are confident to have a go at fixing them.

Stuck lenses seem to be the commonest problem. Simple no-tools measures can fix around 40% of cases.

Disassembly is not usually difficult, but a disassembly guide or video is almost essential. Replacement of the LCD screen should be straightforward, and it may be possible to fix a jumpy mode wheel. If another camera of the same model can be found but with a different fault, it should be possible to cannibalise one to fix the other.

Disassembly of the lens is likely to be significantly harder but still may be attempted as a last resort. a complete replacement lens assembly may be available.

Stuck lens

A lens which refuses to extend, refuses to retract, or gets stuck half way is very common.

No-tools solutions

Sometimes the problem can be due to the battery failing or popping out while the camera is on, though most cameras can cope with this. Try an Internet search for your make and model with the additional key words "stuck lens" for any model-specific tricks.

Most often a stuck lens is caused by dirt getting into the gap between the lens barrel sections. The simplest thing to try is a freshly recharged battery, which might just have the "umph" to overcome the resistance. Plugging in an AV cable sometimes blanks the screen, leaving just a bit more battery power for the lens.

You should be aware that all the following measures carry some level of risk of causing further damage. However, if none of them work the camera will normally be a write-off anyway.

If the lens is stuck partially or fully extended, try gently pulling or pushing the lens barrel as the camera tries to extend or retract it. Usually, a middle section rotates as the lens extends, and you can try gently “helping” it. If the lens won’t extend at all, try shaking it out by knocking the front of the camera against your cupped hand as you turn it on.

Lens barrel cleaning

The next stage is to try to remove any dirt from between the lens barrel sections. Slip a corner of a piece of good quality paper into the gap and gently move it around the circumference of the lens as illustrated. Check the paper often for fraying. If there’s a rubber gasket between the camera body and the outer barrel, never force anything under it.

Now apply a vacuum cleaner crevice tool to the barrel, aiming to apply the greatest possible suction to the gaps you slipped the paper into (as shown). Keep clear of the lens cover on the front of the lens unless it’s fully open as the suction could be sufficient to damage it.

Tapping the lens barrel with a pencil while holding the camera face down can sometimes dislodge a sand particle.

Alternate the paper and vacuum a number of times before giving up. And while you have the vacuum cleaner out, clear all the dust from inside your camera case – it could be what caused the problem in the first place!

Further variants of the suggestions listed here can be found at http://camerarepair.blogspot.co.uk/2007/12/fixing-lens-error-on-digital-camera.html

Sticky lens cover

Sometimes the lens cover, consisting of several metal blades, will stick partially or fully open even when the lens is retracted. This could be due to an obstruction in the channels in which the blades are located, just inside the front of the lens, or a tab which holds them open failing to retract. Probe the channels with a dental probe or a piece of bent wire, but be extremely gentle. If you can be sure the blades are fully open and out of the way you can judiciously apply the vacuum cleaner. If however the blades have got bent there may be little you can do.

Disassembly

Disassembly is not nearly as daunting as it might appear. An Internet search for your make and model of camera plus "disassembly" will often give a detailed guide or video. All you need is a set of precision screwdrivers and an egg box. The egg box is essential. Use it to store the screws and make a careful note of which ones came from where. Replacing a broken screen is fairly straightforward. Just take care removing ribbon cables – some just pull out and push back in, whilst others have a clamping bar which needs to be pulled or lifted, very gently. Keep your fingers away from the flash capacitor (maybe an inch long and located close to the flash) which could give you a nasty jolt if the camera has been switched on recently.

Safety

If you disassemble a camera, take care of the flash capacitor as this may hold a dangerous residual charge long after the camera is switched off, sufficient to give you a nasty shock if you touch its leads or components around it.

The flash capacitor is normally a cylindrical component, typically a couple of cm or so long and maybe 1cm in diameter and with 2 wires coming out of one end. Very often but not always, a protective plastic shield will cover it, considerably reducing the danger.

External links

• External links as bullet points