How to drive screws like a pro: Difference between revisions

(Added Tri-wing)
Line 69: Line 69:
[[File:Screw_Head_-_Hex_Socket.svg|40px|left]]
[[File:Screw_Head_-_Hex_Socket.svg|40px|left]]
These have a hexagonal recess in the head and require either a hexagonal screwdriver or an Allen key, which is simply a piece of hexagonal hardened steel bent into an L-shape. Self-assembly furniture and other items often uses hex screws and come with an Allen key in the pack of screws.
These have a hexagonal recess in the head and require either a hexagonal screwdriver or an Allen key, which is simply a piece of hexagonal hardened steel bent into an L-shape. Self-assembly furniture and other items often uses hex screws and come with an Allen key in the pack of screws.
===Tri-wing===
[[File:Screw Head - Tri-wing.svg|40px|left]]
Several unusual triangular screw heads have been invented but this one is sometimes seen on electronic and domestic electrical equipment where it is used to discourage dismantling by unqualified people, particularly where there might be a serious electric shock hazard.


===Pentalobe===
===Pentalobe===

Revision as of 13:27, 22 October 2017

Tips on how to use screwdrivers most effectively.

Summary

Using a screwdriver is easy - who needs a page like this? True - you will often get away with using the wrong screwdriver or not using it properly, but you can easily damage the head, making it extremely difficult to remove an obstinate screw.

Safety

Warning03.png
Screwdrivers have pointy ends and although not sharp like a knife, they can still cause serious injury if they slip or are misused.


Which way to turn it?

Those who are unaccustomed to using a screwdriver are often uncertain which way to turn it.

The easy way to remember is that it's like a tap (not the modern quarter-turn type):

  • You turn a tap anticlockwise to open it and release the flow of water.
    • You turn a screw anticlockwise to undo it and release whatever it's holding.
  • You turn a tap clockwise to turn it off and hold the water supply.
    • You turn a screw clockwise to tighten it and hold whatever it's fixing.

How to use a screwdriver

Removing a screw

The key thing is not to let the screwdriver slip. If it does it's liable to damage the head, or "cam out", which will make it harder or even impossible to remove the screw.

First of all, make sure you're using the right type and size of screwdriver (see next section), particularly if the screw might be tight.

Make sure you're holding the screwdriver straight and not at an angle to the screw.

Press hard! If you can't turn the screw easily, PRESS VERY HARD!! If the screwdriver slips, you're not pressing hard enough. But be aware of what might be taking the strain underneath the screw.

If the screw is rusty you may be able to loosen it by applying a little penetrating oil to the thread and leaving it to soak in.

Inserting a screw

When inserting a screw it's very important to make sure it's straight otherwise you can get a "crossed thread" which will damage the screw or the threaded hole, or both.

If you have any difficulty at all in getting the screw to engage with the thread of the hole, first of all turn it anticlockwise (as if undoing it) whilst pressing gently. You should feel a little click as the first thread of the screw engages with the first thread of the hole. Immediately start turning it clockwise to tighten it.

You can practice this on a jam jar, or any kind of container with a screw top. People often put the lid on crooked so that the screw thread doesn't engage properly and the container doesn't seal. Turn the lid anticlockwise until you feel the click, then tighten it as normal and you should find it goes on straight.

A screw should be well tightened, but never so much that the screwdriver slips and damages the screw head. If you're sure the thread has engaged properly but it's still very stiff, lubricate it with just a smear of Vaseline or silicone grease or soap.

Types of screw head

There are many different types of screw head but just a few common ones, and each comes in a range of sizes. With some types the wrong size won't work at all, and with the more forgiving types the wrong size will at best give you sub-optimal leverage and at worst will damage the screw head.

The following are the types of screw you are most likely to come across.

Slotted

Screw Head - Slotted.svg

The commonest and oldest type of screw head just consists of a slot, and is driven by a flat bladed screwdriver. It has the disadvantage that the head is easily damaged and the screwdriver blade easily slips out of one end or the other of the slot. Choose a screwdriver with a blade which best fits both the width and length of the slot and make sure it's centred within the slot.

In a tamper-resistant version the slot is interrupted in the centre, making it impossible to use a standard flat screwdriver. This requires a special screwdriver with a slot in the centre of the blade. This version is quite often seen in domestic electrical and kitchenware items.

Phillips

Screw Head - Phillips.svg

This is a common form of cross-head screw, not to be confused with the Pozidriv (see below). Phillips screwdrivers come in sizes 000, 00, 0, 1, 2, 3 (in increasing order of size), sometimes prefixed with "PH", to distinguish them from Pozidriv. and you should use the right size if possible.

Pozidriv

Screw Head - Pozidrive.svg

Superficially similar to a Phillips screw, a Pozidriv screw is distinguished by the tick marks at 45 degrees and is designed to allow greater torque to be applied without risk of camming out. Pozidriv screwdrivers come in sizes 0 - 5, prefixed with "PZ".

A Pozidriv screwdriver has a less pointed tip than a Phillips and so it is inadvisable to use a Phillips screwdriver on Pozidriv screws as the screw head is liable to be damaged if more than minimal torque is applied.

Torx

Screw Head - Torx.svg

Common in electronic equipment, a Torx screw requires exactly the right screwdriver. Correctly used, it gives very good resistance to cam-out without having to press excessively hard. Torx screwdrivers come in a wide range of sizes, from T1 (smallest) up to T100. The smaller sizes from around T6 to T10 are commonest in electronic repair.

A tamper-resistant version has a small pin in the centre of the recess, requiring a screwdriver with a corresponding hole in the centre of the tip.

Hex

Screw Head - Hex Socket.svg

These have a hexagonal recess in the head and require either a hexagonal screwdriver or an Allen key, which is simply a piece of hexagonal hardened steel bent into an L-shape. Self-assembly furniture and other items often uses hex screws and come with an Allen key in the pack of screws.

Tri-wing

Screw Head - Tri-wing.svg

Several unusual triangular screw heads have been invented but this one is sometimes seen on electronic and domestic electrical equipment where it is used to discourage dismantling by unqualified people, particularly where there might be a serious electric shock hazard.

Pentalobe

Pentalobular.svg

At first glance resembling a Torx screw, these have 5 lobes instead of 6. They are commonly used by Apple as a tamper-resistant screw, but the screwdrivers are readily available. If you order a replacement iPhone battery or screen it will often come with a cheap pentalobe screwdriver. Due to their small size, these can be fairly easily damaged.

Others

In addition to the above, less often you may come across various other types of screw. Many are listed in the Wikipedia article List of screw drives.

Choosing your screwdrivers

Many people will have an odd screwdriver or two in a kitchen draw, but a reasonably good set is almost essential for even the simplest repair tasks. However many screwdrivers you have, from time to time you may find you haven't got the right one for the job. But a well chosen selection will satisfy nearly all you needs. There are several options.

Single screwdrivers

You can buy single screwdrivers individually or in a set, and a set containing 2 or 3 each of flat bladed, Phillips and Posidriv would make an excellent start. If they come in a box to keep them together then so much the better.

For more delicate work you will need some smaller screwdrivers such as jeweller's screwdrivers, however, these tend not to allow a good grip for undoing a tight screw without slipping.

Single screwdrivers have reasonably long shafts allowing them to reach recessed screws easily.

Screwdrivers with separate bits

A screwdriver set with separate 6mm bits.

Many people favour a screwdriver set containing a single handle and a range of bits. Since the handle is the bulky part this allows you to be prepared for a wide range of screw types with a single compact set in a box. Choose a set with a comfortable handle allowing a good grip. Many have a useful ratchet action that you can set to clockwise or anticlockwise.

A set of security screwdriver bits.

Most of these take standard 6mm hex bits, and sets of additional bits are available for unusual and security screws.

File:LongSecrewdriverBits.jpg
A set of long screwdriver bits.

A disadvantage is that the standard bits are very short, which can make it difficult to reach recessed screws. But you can also get sets of extra long bits.

A precision screwdriver set.

In addition to the sets taking 6mm bits you can get precision screwdriver sets for working on smaller electronic equipment such as smartphones or cameras. These tend to be a much better option than jeweller's screwdrivers.

Electric screwdrivers

If you're face with a lot of screws, or screws which screw in a long way, an electric screwdriver is a tempting option. These generally come with a set of 6mm bits which you can supplement as required.

A disadvantage with the cheaper ones is that it makes it very easy to cam out a screw head since you have little control over the torque applied. Consequently you should only use it on screws which are fairly easily turned, and never on one you can't turn by hand. Also, if using it to insert screws you are probably better off leaving the last turn or two to do by hand.

The more sophisticated electric screwdrivers have a slip clutch which limits the torque applied, but this needs to be set correctly, and it doesn't eliminate the risk of cam out and damage to the screw head if you don't press hard enough.

Rescuing damaged screws

If you end up with a damaged screw then all is not lost. There are still a few options.

But before starting, ask yourself a silly question: were you turning it the right way? Of course you know that you turn a screw anticlockwise to undo it - you're not stupid. But just occasionally you'll find a left handed screw which turns the other way, most usually on a rotating shaft where the direction of rotation might otherwise cause the screw to come loose. A screw holding a fan, an impeller or a pulley on the end of the shaft of an electric motor might have a left handed thread for this reason.

Small screws in electronic equipment are probably the hardest since there is very little undamaged metal to play with. This iFixit guide covers most of the options, which are summarised below:

  • A different screwdriver may work, such as a larger size of a flat bladed one.
  • Apply the screwdriver through a rubber band to get extra grip.
  • If sufficient of the head is accessible you may be able to grip it with pliers.
  • Add a drop of superglue to the screw head, insert the screwdriver and hold it steady while the glue sets, then try turning it.
  • Using a dremel, cut a slot in the screw head and use a flat bladed screwdriver

With larger screws there are a few more possibilities:

  • Drill a hole in the screw head and insert a screw extractor. This has a left handed tapered thread in hardened steel which you screw anticlockwise into the hole. Provided you can get it to grip the screw head this will do the job if anything will.
  • Find the largest screwdriver whose tip will reach the bottom of the recess in the screw head. Then fill the recess in the screw head with steel reinforced epoxy. As it just begins to harden, carefully press the screwdriver tip into the epoxy to make an indentation, then leave it to fully harden before trying with the same screwdriver.
  • If the thread is rusted, then apply a little penetrating oil to ease it, and leave it to soak in. For this, most people immediately think of WD40 but there are many discussion threads on the Internet suggesting that PB Blaster is much better.
  • Heat from a butane blow torch may also help in the case of a badly corroded screw, provided this won't damage other parts.
  • Tapping it with a hammer may help break up any rust.

Whatever method you choose, you may simply end up with the screw head shearing off, which may allow you to dismantle whatever it was but may then leave you with another problem.