Personal e-transport - temp

This page covers e-bikes, e-scooters, hoverboards and similar battery-powered personal transport devices.

Summary

All types of personal e-transport consist of various electrical subsystems in addition to the mechanical frame and drive, considered in turn, each being prone to different faults.

Safety

Warning03.png
E-bikes and scooters etc all include a fairly powerful rechargeable lithium battery. Physically or electrically abused, this can present a serious fire risk. If possible, avoid charging in the house, and do not leave the charger connected for an extended period.
Always use the charger that came with your device. If this is impossible, take great care to ensure a replacement charger is fully compatible. Cheap subsitutes may costitute a severe fire risk
If refurbishing a battery with new cells it's essential that you understand how to correctly charge and balance the cells.
The motor is likely to be quite powerful and any associated gears could cause serious injury to fingers if it started unexpectedly. Disconnect the battery as the first thing you do and reconnect it as the last.

Basic Battery Faults Diagnosis

Start with the basics by trying to charge your battery with the official charger that came with your electric vehicle. The owner's manual should tell you how your vehicle indicates (usually by means of a LED) whether it is charging and when fully charged. When fully charged, check the battery output voltage with a multimeter by connecting the multimeter to the battery terminals. If the measured voltage is significantly lower than the battery's rated voltage you might need to get a replacement or have it fixed by a professional repair shop.

The BMS (Battery Management System) controls the balanced charging and discharging of individual cells. If you can get physical access to the BMS board, without touching any of the battery's cells or contacts, check the thickness of the wires connecting the BMS board to the individual cells. Often BMS manufacturers will use minimum acceptable guage wires, leading to bad connections or the battery quickly losing efficiency. In such a case a new higher quality BMS may be required, fully capable of handling the current your device requires. DO NOT attempt to fit this unless you can easily gain access to the BMS and are fully competent to replace it. Otherwise, seek the services of aqualified technicien.

Electric Motor Problems

Type of electric motor

Most electric scooters, bicycles and hoverboards use brushless motors. If your vehicle has a brushed DC motor then changing the graphite brushes regurarly to avoid sparks and damage to your motor's commutator should be a part of your maintenance every once in a while.

Basic parts of an electric scooter
Basic parts of an electric scooter

Identify the electric motor or motors of your vehicle

  • In electric scooters the motor is embedded within the wheel, usually leaving no room for air to pass through the it. Identify whether the back or front wheel is the one powered. In certain cases it might be both.
  • In hoverboards it's usual for both wheels to have embedded hub motors in their wheels.
Mid Drive motor inside frame of bicycle
Mid Drive motor inside frame of bicycle
  • In electric bikes the motor can be either embedded within the frame close to the pedals, or can be found at most commonly on the hub of the back wheel.

Grinding sounds from tthe motor

If the motor doesn't spin freely but makes a grinding noise as it turns you might have a bad bearing that needs changing. Generally, you need to dissasemble the wheel to reach the bearing, and then replace it with a new one of the same size, and regrease it. Reassemble the wheel and check that the grinding noise is gone.

If the noise is not constant but speeds up as the motor speeds up, the motor may have an embedded disk brake which you should check. If this is misaliged then it may be the source of your problem.

If the motor shakes or vibrates when powered on

If the motor vibrates or shakes when turned on then perhaps the motor has internal issues such as (in the caseof a brushe motor) worn or sparking brushes.

Alternatively, the power supply may be unable to supply the motor with sufficient current. Reassemble the vehicle completely, and connect the battery. Check whether the battery reading fluctuates at the display during the startup of the motor. If the motor keeps vibrating then it's likely to be either a faulty battery or controller since both are required to function correctly for the motor to reach its maximum speed.

Powering the motor from another power supply

To independantly power a motor intended for an electric vehicle you need a power supply capable of outputting the same the voltage and at least the same current as the vehicle's battery, usually written on the battery itself. Do not attempt this unless you are competent to work with high currents at up to 48V, but instead, seek professional help.

If you are a competent to do so, identify the negative and positive motor terminals and apply a voltage through an appropriate power supply to turn the motor. If the motor does not move, try giving it a spin first by hand. Turning the motor by spinning the wheel helps the motor start, since electric motors can demand three times the normal current during starting. By turning the motor, you avoid demanding such a big starting current from your power supply.

Electronic problems

Dissassemble to access the electronics

After you've identified the electric motor or motors in your vehicle try to find a disassembly video or written tutorial and follow it closely. This is important because it contains a powerful battery and damage or a fire could result from imporoper disassembly. In particular, for safety, remove the battery as soon as possible without damaging anythig.

Choose a replacement speed controller board

If you looking for a replacement electronic speed controller (ESC) for your electric vehicle in general you need one capable of handling the voltage produced by the battery and its maximum current rating. These figures are usually written on a label on the battery itself or may be in the owners manual. Choosing a speed controller capable of handling more current than your current may result in a faster final motor speed but may deplete the battery faster, requiring more frequent charging and may also shorten the battery life. For lower current speed controller boards the opposite is true, resulting in a lower final motor speed and slower overall vehicle but your battery won't deplete as fast. Make sure if you are replacing the controller boards that they are fitted the same way the originals. They must be firmly bolted to the aluminium frame with thermal paste to aid heat conduction to the frame, otherwise they are likely to overheat and fail.

Checking the electronic circuits

If you know how to use the continuity mode in your multimeter you may be able to identify any potential short circuits, grounding faults or other apparent faults on the controller board or between it and other parts. If the controller boards are covered with silicone for protection and waterproofing, continuity checks on the board itself will not be possible. Carry out a careful visual check of the boards to make sure there is no evidence of water damage, or signs of burnt or improperly soldered components. Keep in mind that in addition to the controller board there will often be other boards to drive the display, the electric motor and other subsystems. An understanding of the symptoms may help you determine which board is at fault and whether it might be relaceable.

What is the gray paste on top of my speed controller?

Since speed controller electronic boards usually handle high voltages and amps they usually heat up quickly and need some form of thermal management to keep cool and working efficiently. Sometimes thermal paste, yes like the one used for computer CPUs, can be applied to one side of the controller boards for them to dissipate heat along the aluminum frame of the electric scooter, under the part where the user usually stands. This is usually the case in electric scooters but I am not aware if hoverboards, or electric bikes follow the same principle.

How to tell if moisture is the cause of concern for your vehicle's electronics?

Most electric vehicles feature moisture detection strips that turn pink in the presence of moisture. If you encounter those strips while opening the vehicle's electronics enclosure and see they have turned into a pink color you might be dealing with moisture or humidity damage to your electronics. If the enclosure also contains the battery of the vehicle visually check its plastic cover to see if it's broken or teared up. If that covering is torn apart or open somewhere, moisture might have gone to your battery.

Mechanical Problems

Basic alignment check with metal ruler for electric scooter
Basic alignment check with metal ruler for electric scooter

Does the electric scooter drive in a curved line, feels unsafe or you want to check its alignment?

If the electric scooter doesn't keep a straight direction when you are driving in a straight line as much as possible you can check the alignment of the back wheel with the frame. To do that put a metal ruler across the frame with the ruler touching as much of the lower frame chassis and the motor wheel bracket as much as possible. If the metal ruler touches the entire frame and back wheel bracket in a uniform way without gaps then you are in luck because the scooter is properly aligned. If there are small gaps between the frame or bracket of the wheel and the metal ruler then that means that possibly the fork of the scooter is possible not straight due to a collision or other mechanical reason and needs replacing. In this case, I define as the fork of the scooter as the mechanical part that is holding together the neck of the scooter with the lower chassis containing usually the battery and wheels.

Proper movement along the neck of the scooter (blue). Movement showing some mechanical failure (red).
Proper movement left to right along the neck of the scooter (blue). Movement back and forth of the neck showing some mechanical failure (red).

Does the neck of an electric scooter feel unsafe, or wiggles back and forth?

The neck of the scooter which connects the steering wheel and lower chassis of the vehicle shouldn't wiggle back and forth or feel unsafe. If it does wiggle and not just turn right and left securely, there might be some issue with the metal chassis of the neck of the scooter or fork. Once again, I define as the fork of the scooter as the mechanical part that is holding together the top part of the scooter or neck that contains the steering wheel and controls, with the lower chassis that usually contains the battery and wheels.

A metal part of my electric scooter has been broken and I urgently need my vehicle fixed:

Sometimes mechanical parts connecting the frame together like the fork or neck of an electric scooter might bend or break. In that case, you can get an appropriate replacement from a trusted seller but that might take some time you don't wish to spend without a working vehicle. For metal or mechanical parts, asking local metalworking shops in your area, might be worth it, as they might be able to help with your problem by designing and making a replacement part themselves. Also electric scooter parts may be interchangeable from one brand to another if modified properly with professional help from metalworking and repair businesses. This isn't really recommended as a repair you should do yourself or in general but it's mentioned here as an alternative option for a temporary fix that might save you a lot of time you would otherwise wait to get an appropriate part from the manufacturer. Remember to always use caution when driving such electric vehicles that have such repair or modified parts and realise that this is perhaps one of the many ways to break any warranty you might have for the vehicle.