Steam Irons: Difference between revisions

No edit summary
Line 1: Line 1:
The first challenge with modern steam irons is often how to disassemble them, and unfortunately the repair options are often limited, but some of what can be attempted is described here.
The first challenge with a modern steam irons may be to disassemble it. Unfortunately the repair options can be limited, nevertheess some of what can be attempted is described here.


==Summary==
==Summary==
Steam irons are quite often seen at Restart parties. They can be challenging to open, and as with any appliance which mixes water and electricity the fault can often be due to a failure, ultimately, to keep them sufficiently apart.
Steam irons are regularly seen at Restart parties. They can be challenging to open, and as with any appliance which mixes water and electricity the fault can often be due to a failure, ultimately, to keep them sufficiently apart.


==Disassembly==
==Disassembly==
[[File:Img_0373a.jpg|200px|thumb|right|Steam iron disassembly.]]
[[File:Img_0373a.jpg|200px|thumb|right|Steam iron disassembly.]]
Usually there will be one or two easily accessible screws at the back of the handle but these may only release that part of the handle. Another screw or screws near the front may be hidden for example under the steam button, but even after removing these the handle cover can be tricky to remove. Often there will be a series of clips down the sides, but this may not be all. In the iron illustrated there was another clip to be released on the top just forward of the cable which required the whole of the top cover to be pushed forward.
Usually there will be one or two easily accessible screws at the back of the handle of the iron. These typically release a cover providing access to the cable connections. If the problem is a worn cable, hopefully this may be all the disassembly required.
 
Another screw or screws near the front may be hidden for example under the steam button, but even after removing these the handle cover can be tricky to remove. Often there will be a series of clips down the sides, but this may not be all. In the iron illustrated there was another clip to be released on the top just forward of the cable which required the whole of the top cover to be pushed forward.


With the top cover off it should be possible to find the screws which release the whole of the plastic top, in order to access the thermostat etc. and (if not already accessible) to replace the mains lead.
With the top cover off it should be possible to find the screws which release the whole of the plastic top, in order to access the thermostat etc. and (if not already accessible) to replace the mains lead.
Line 14: Line 16:
== Specific Faults ==
== Specific Faults ==
=== Worn Flex ===
=== Worn Flex ===
Because irons are moved around a lot, bending the mains flex, one or more of the conductors can break, usually close to the iron body.
Because irons are moved around a lot, this causes strain on the mains lead. One or more of the conductors can break, usually close to the iron body. Locating the break may be tricky, although usually it will be close to the body and can often be felt by bending the flex conductors individually.
Locating the break may be tricky, although usually it will be close to the body and can often be felt by bending the flex conductors individually.


Either cut the current flex back to before the break then reconnect it or replace it with a compatible heat-resistant flex.
You can cut the existing flex back to before the break then reconnect it, but for safety and lengevity you will probably do better by replacing it with a compatible heat-resistant flex. Seartch online for cotton covered iron flex, or try a local domestic appliance repair shop if you have one.


=== Thermostat ===
=== Thermostat ===
The thermostat switches the element off when the iron gets up to temperature and back on when it cools down a bit.
The thermostat switches the element off when the iron gets up to temperature and back on as it cools down a bit.
Usually it consists of a pair of contacts, one of which is a bimetallic strip which bends away from the other when it heats up.
Usually it consists of a pair of contacts, one of which is a bimetallic strip which bends away from the other when it heats up.
The distance between the contacts is adjusted by a threaded shaft attached to the temperature control knob.
The distance between the contacts is adjusted by a threaded shaft attached to the temperature control knob.


If the electrical continuity is otherwise good and the element shows the correct resistance, but the iron won't heat up, try cleaning the thermostat contacts and checking that they actually do contact electrically when they come together.
If the electrical continuity is otherwise good and the element shows the correct resistance, but the iron won't heat up, try cleaning the thermostat contacts and checking that they do actually make electrical contact when they come together.


=== No Steam ===
=== No Steam ===
Line 30: Line 31:


Another possibility is that there is a hole which allows air into the water chamber which has got blocked:
Another possibility is that there is a hole which allows air into the water chamber which has got blocked:
the symptom in this case will usually be an initial small puff of steam followed by nothing.
the symptom in this case will usually be an initial small puff of steam followed by nothing. A good place to start looking for the hole is in the filler cap.
A good place to start looking for the hole is in the filler cap.


[[Category:General]]
[[Category:General]]

Revision as of 21:11, 28 March 2020

The first challenge with a modern steam irons may be to disassemble it. Unfortunately the repair options can be limited, nevertheess some of what can be attempted is described here.

Summary

Steam irons are regularly seen at Restart parties. They can be challenging to open, and as with any appliance which mixes water and electricity the fault can often be due to a failure, ultimately, to keep them sufficiently apart.

Disassembly

Steam iron disassembly.

Usually there will be one or two easily accessible screws at the back of the handle of the iron. These typically release a cover providing access to the cable connections. If the problem is a worn cable, hopefully this may be all the disassembly required.

Another screw or screws near the front may be hidden for example under the steam button, but even after removing these the handle cover can be tricky to remove. Often there will be a series of clips down the sides, but this may not be all. In the iron illustrated there was another clip to be released on the top just forward of the cable which required the whole of the top cover to be pushed forward.

With the top cover off it should be possible to find the screws which release the whole of the plastic top, in order to access the thermostat etc. and (if not already accessible) to replace the mains lead.

On reassembly, ensure that any tubes associated with the water reservoir and steam delivery are properly connected.

Specific Faults

Worn Flex

Because irons are moved around a lot, this causes strain on the mains lead. One or more of the conductors can break, usually close to the iron body. Locating the break may be tricky, although usually it will be close to the body and can often be felt by bending the flex conductors individually.

You can cut the existing flex back to before the break then reconnect it, but for safety and lengevity you will probably do better by replacing it with a compatible heat-resistant flex. Seartch online for cotton covered iron flex, or try a local domestic appliance repair shop if you have one.

Thermostat

The thermostat switches the element off when the iron gets up to temperature and back on as it cools down a bit. Usually it consists of a pair of contacts, one of which is a bimetallic strip which bends away from the other when it heats up. The distance between the contacts is adjusted by a threaded shaft attached to the temperature control knob.

If the electrical continuity is otherwise good and the element shows the correct resistance, but the iron won't heat up, try cleaning the thermostat contacts and checking that they do actually make electrical contact when they come together.

No Steam

If the iron is heating up but isn't producing steam, this is almost certainly a mechanical problem, usually caused by limescale: descale it.

Another possibility is that there is a hole which allows air into the water chamber which has got blocked: the symptom in this case will usually be an initial small puff of steam followed by nothing. A good place to start looking for the hole is in the filler cap.