How dimmers and motor controllers work: Difference between revisions

No edit summary
Line 24: Line 24:


Thus, depending on the setting of the variable resistor VR1, power will be supplied to the lamp or motor for only a portion of each half cycle as shown in the graphic, so varying the lamp brightness or the speed of the motor.
Thus, depending on the setting of the variable resistor VR1, power will be supplied to the lamp or motor for only a portion of each half cycle as shown in the graphic, so varying the lamp brightness or the speed of the motor.
In practice, there are likely to be a few additional components to absorb spikes in the mains voltage that may otherwise cause unreliable operation or possibly even damage the triac. Electric motors are a common culprit, so a motor speed controller will always have this provision, even though a motor itself will be fitted with similar transient suppression components.


==Faults==
==Faults==
Line 30: Line 32:
==Low-energy lamp dimmers==
==Low-energy lamp dimmers==
Old fashioned dimmer switches are unsuitable for use with low energy bulbs as they tend not to like the current being switched on suddenly in the middle of a half cycle. Modern dimmer switches operate differently, often including a microcontroller, and instead, switch the current off part way through each half cycle, or offer several modes of operation. Even so, it's important to use bulbs which are specifically marked as "dimmable".
Old fashioned dimmer switches are unsuitable for use with low energy bulbs as they tend not to like the current being switched on suddenly in the middle of a half cycle. Modern dimmer switches operate differently, often including a microcontroller, and instead, switch the current off part way through each half cycle, or offer several modes of operation. Even so, it's important to use bulbs which are specifically marked as "dimmable".
==LED dimmer switches==


[[Category:General]]
[[Category:General]]

Revision as of 22:37, 11 January 2024

Motor controllers and dimmers are commonly built around a simple circuit. Sometimes, this can fail, but may well be repairable.

Summary

Many household appliances such as vacuum cleaners and kitchen mixers and blenders have a continuously variable speed control using a triac. Older light dimmers use the same circuit though they work poorly with low energy CCFL and LED bulbs

Safety

Warning03.png
As with all mains-operated devices, an understanding of electrical safety is essential for any dissasembly or repair.


Mode of Operation

A basic triac dimmer circuit.

The simple circuit shown in the graphic was used in the original light dimmers often fitted in place of a normal on/off light switch for old fashioned incandescent light bulbs. The same circuit is still used in motor speed controllers in many appliances. (A more sophisticated circuit is required for modern low energy light bulbs.)

The key circuit element is a triac, a 3-terminal semiconductor device with few if any other applications. It operates as a switch, controlled by the the gate (the side connection in the diagram). Initially it allows no current to pass, but when a voltage is applied to the gate it suddenly turns on and remains on (irrespective of the gate voltage) until the mains supply drops to zero at the end of a half-cycle. A triac is in fact very similar to a thyristor or SCR (silicon controlled recitifier) except that it works equally well with either positive or negative voltages. This makes it ideal for use in AC circuits, in which the voltage reverses twice per cycle.

You will notice another component in the circuit with a similar symbol, but lacking a gate. This is a diac, similar to a triac except that it has no gate. Instead, it suddenly turns on when the voltage across it reaches a certain value, perhaps 35V.

The waveform produced by a simple dimmer.

As the mains voltage rises at the start of a cycle, current flows through the resistor R1 and variable resistor VR1, charging the capacitor C1. This continues until the voltage across C1 is sufficient to turn on the diac. The capacitor discharges through the diac and into the triac gate, switching it on. It remains on for the rest of the cycle, only switching off when the mains voltage drops to zero, after which the same happens in the other half cycle.

Thus, depending on the setting of the variable resistor VR1, power will be supplied to the lamp or motor for only a portion of each half cycle as shown in the graphic, so varying the lamp brightness or the speed of the motor.

In practice, there are likely to be a few additional components to absorb spikes in the mains voltage that may otherwise cause unreliable operation or possibly even damage the triac. Electric motors are a common culprit, so a motor speed controller will always have this provision, even though a motor itself will be fitted with similar transient suppression components.

Faults

Either the diac or the triac can fail, causing a motor either to run at full speed only, or not at all. First try replacing the diac. Any with a voltage rating in the 30 - 40V range should do. If that doesn't fix it, check the markings on the triac and replace it it with one of the same type.

Low-energy lamp dimmers

Old fashioned dimmer switches are unsuitable for use with low energy bulbs as they tend not to like the current being switched on suddenly in the middle of a half cycle. Modern dimmer switches operate differently, often including a microcontroller, and instead, switch the current off part way through each half cycle, or offer several modes of operation. Even so, it's important to use bulbs which are specifically marked as "dimmable".